MINERAL PROCESSING KNOWLEDGE · CRUSHING AND GRINDING
See how PE, PEV and PEX jaw crushers differ in chamber design, duty and adjustment, and where each family belongs in a crushing circuit.
Technical overview. Actual process selection depends on representative ore samples, mineralogy, testwork and site conditions.
Jaw crushers are often specified late, after the flowsheet is settled, when the only question left is which model number fits the budget. That order of work hides a real decision. The PE, PEV and PEX families are built for different positions in a crushing circuit and for different feed conditions, and their catalogues carry different columns because each family is judged on different criteria. A primary machine is judged by the largest lump it will swallow without bridging. A fine machine is judged by the tightest setting it can hold without packing.
Technical note: What follows explains, at the level of principle, how the three jaw crusher families differ and how their published data should be read. It is not a sizing calculation, an engineering design or a performance guarantee. Final selection depends on representative feed samples, hardness testing and review of the whole circuit by a qualified engineer.
1. What actually separates the three families
Every jaw crusher breaks rock between a fixed jaw and a swing jaw, and every one is driven by an eccentric shaft. What differs is the geometry of the chamber and the motion of the swinging jaw, and those decide which feed a machine accepts and which product it can hold.
- PE, the general-purpose primary machine. A single-toggle linkage drives the swing jaw from an eccentric shaft carried between the side plates. The chamber is deep, the toggle angle is steep and the jaw plates are symmetrical, so the machine is built to take a lumpy, unscreened run-of-mine feed. The range runs from PE250×400 with its 250×400 mm feed opening to PE1500×1800, with a 1500×1800 mm opening, a 1200 mm maximum feed size and a 280 kW motor.
- PEV, the European-pattern primary. This family is published with a machine weight instead of outline dimensions, and it lists main shaft speed, a column the PE table does not carry. The frame is heavier for the same opening (PEV860×1100 is listed at 26.5 t) and the swing jaw runs on a longer stroke, which spreads the crushing action over more of the chamber. Shaft speed falls as the model grows, from 270 r/min on PEV400×600 to 200 r/min on PEV900×1200.
- PEX, the fine-crushing machine. PEX chambers are long and shallow. The jaw plates reach down towards the discharge end, so rock is squeezed repeatedly near the bottom of the stroke; that is what allows settings far tighter than a PE of similar width can hold. PEX150×750 is offered between 10 mm and 40 mm, and the largest model, PEX300×1300, still runs down to 25 mm.
2. Reading the specification table without being misled
Published capacity is a range on every jaw crusher, because tonnes per hour depend on the discharge setting: set the same machine coarse and it passes far more material than when set fine. The table below places representative models from the three families side by side.
| Family | Model | Max. feed size (mm) | Discharge setting (mm) | Capacity (t/h) | Motor power (kW) |
|---|---|---|---|---|---|
| PE | PE400×600 | 350 | 40-90 | 15-60 | 30 |
| PE | PE750×1060 | 630 | 60-150 | 110-380 | 110 |
| PE | PE1200×1500 | 1020 | 150-300 | 400-800 | 220 |
| PEV | PEV400×600 | 380 | 40-80 | 20-65 | 30 |
| PEV | PEV750×1100 | 630 | 80-175 | 110-320 | 110 |
| PEV | PEV900×1200 | 750 | 100-220 | 220-380 | 132 |
| PEX | PEX150×750 | 120 | 10-40 | 5-16 | 15 |
| PEX | PEX250×1200 | 210 | 15-60 | 25-80 | 37 |
| PEX | PEX300×1300 | 250 | 25-60 | 30-105 | 55 |
Three readings follow from those figures. First, the maximum feed size always sits below the feed opening width: PE250×400 has a 250×400 mm opening and a 210 mm maximum feed, and the pattern repeats right across the range. The opening width limits the lump, and the lump limits the blast design, so the two have to be planned together. Second, at comparable motor power the PE and PEV families are close in throughput: PE750×1060 is quoted at 110-380 t/h on 110 kW and PEV750×1100 at 110-320 t/h on the same 110 kW, while PEV400×600 passes slightly more than PE400×600 on an identical 30 kW motor. The European pattern is not automatically a capacity upgrade; its differences show up in the setting range, the heavier build of the frame and the adjustment routine. Third, PEX models are long and narrow, so width sets the lump while length sets the throughput. Judging them on width alone undersizes the machine: PEX250×1200 is quoted at 25-80 t/h, against 15-60 t/h for the wider-looking PE400×600.
3. Matching the family to a circuit position
The position in the flowsheet, not the model number, should drive the choice of family. A primary crusher stands directly behind the feeder and sees the mine at its worst, including slabs that should never have been loaded. A secondary or tertiary machine sees screened, predictable feed, and there the tight setting and long chamber of a PEX machine earn their place. Four checks settle most enquiries.
- Largest lump into the plant. Compare the mine plan with the maximum feed size of the candidate model, not with the feed opening. Bridging a chamber costs more than a larger machine does.
- Product band required downstream. If the next stage needs material inside a narrow band, quote the setting range first and the tonnage second; a wide range upstream keeps later stages stable.
- Fed material condition. A fine crusher should be fed scalped rock rather than raw primary product, so a vibrating feeder and a screen ahead of the chamber are part of the decision.
- Adjustment frequency. A circuit that resets the chamber every shift places different demands on the machine than one that runs for months on a single setting.
Conclusion
PE, PEV and PEX are three duties rather than three quality levels of the same machine. PE is the unscreened primary workhorse with the widest spread of sizes. PEV offers a longer stroke with a published shaft speed and weight, useful where chamber geometry and maintenance access matter more than headline tonnage. PEX holds a tight setting on screened feed and should be sized from its jaw length as much as its width. Check the largest lump, the product band and the feed condition before the model number is fixed.
How LiCheng Tech can help
Send us the feed size distribution, the largest lump the mine produces, the product you need and the tonnage you must hold. We will shortlist models from the PE, PEV and PEX ranges on those inputs, confirm the published figures with the supplying factory and set out where each candidate is strong and where it is not.
Explore the Jaw Crusher pages, review the wider Mineral Processing flowsheet, or send your project information.
